SIPLUS CPU 317F-2 DP производства Siemens

The fail-safe CPU with a large program memory and quantity framework for demanding applications
For configuring a fail-safe automation system for plants with increased safety requirements
Complies with safety requirements up to SIL 3 according to IEC 61508 and up to Cat. 4 according to EN 954-1
Fail-safe I/O modules can be connected in a distributed configuration to both integral PROFIBUS DP interfaces (PROFIsafe)
The fail-safe I/O modules of ET 200M can be also centrally connected
The standard modules for non-safety applications can be operated both centrally and locally

Micro Memory Card required for CPU operation.

Note:

SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme-specific information was added.

	SIPLUS CPU 317F-2 DP
Order number	6AG1 317-6FF03-2AB0	6AG1 317-6FF03-2AY0
Order No. based on	6ES7 317-6FF03-0AB0	6ES7 317-6FF03-0AB0
Ambient temperature range	-25 ... +60 °C
Conformal coating	Coating of the printed circuit boards and the electronic components.
Technical data	The technical data of the standard product applies except for the environmental conditions.
Compliant with the standards for electronic equipment used on railway rolling stock (EN 50155, temperature T1, category 1).	No	Yes
Technical data	The technical data is identical to that of the based on modules.
Ambient conditions
Relative humidity	5 ... 100%, condensation allowed

Technical documentation on SIPLUS can be found here:
http://www.siemens.de/siplus-extreme

The CPU 317F-2 DP allows a fail-safe automation system to be implemented for plants with increased safety requirements, especially in manufacturing automation.

The safety-oriented communication between the F-CPU and the fail-safe I/O modules is performed on the basis of the PROFIsafe profile.

A SIMATIC Micro Memory Card is required for operation of the CPU.

The CPU 317F-2 DP is equipped with the following:

Microprocessor;
the processor achieves an execution time of approximately 25 ns per binary instruction and 160 µs per floating-point operation. The CPU 317F-2 DP is significantly superior regarding processing speed, particularly where word or double-word commands and 32 bit fixed-point commands are concerned
Memory;
1.5 MB high-speed work memory for safety-relevant and standard program sections; increased memory space requirements must be expected (5 times larger) if safety-relevant program sections are implemented. SIMATIC Micro Memory Cards (8 MB max.) as load memory for the program also allow the project to be stored in the CPU (complete with symbols and comments) and can be used for data archiving and recipe management.
Flexible expansion
up to 32 modules (four-tier configuration)
Combined MPI/DP interface
The first MPI/DP integrated interface can establish as many as 32 connections simultaneously to S7-300/400 or connections to programming device, PC, OP. Among these connections, one is always reserved for programming devices and another for OPs. A simple network with up to 32 CPUs can be configured with the MPI interfaces and "global data communication".
The MPI interface can be reconfigured from an MPI to a DP interface. The DP interface can be used as a DP master or as a DP slave.
PROFIBUS DP interface;
The second integrated interface of the CPU 317F-2 DP is a pure PROFIBUS DP interface that can be used as a DP master or as a DP slave. It allows a distributed automation configuration with high speeds and simple handling. From the user's point of view, the distributed I/Os are treated the same as central I/Os (identical configuration, addressing and programming).
The PROFIBUS DP V1 standard is supported in full. This increases the scope of DP V1 standard slaves in terms of diagnostics and parameterization capability.
Limitation: It is impossible to operate both interfaces simultaneously as slaves.

Distributed I/O stations containing fail-safe I/O modules can be connected through the two integrated PROFIBUS DP interfaces. The fail-safe I/O modules of ET 200M can also be installed in central and safety-related configurations. The fail-safe I/O modules of ET 200M can also be centrally implemented. Safety-related communication is performed over PROFIBUS DP with the PROFIsafe profile.

Password protection;
a password concept protects the user program from unauthorized access.
Diagnostics buffer;
the last 100 errors and interrupt events are saved in a buffer for diagnostics purposes.
Maintenance-free data backup;
the CPU automatically saves all data in case of power failure so that the data are available again unchanged when the power returns

Configurable attributes

STEP 7 can be used to parameterize both S7 configurations and the properties and responses of the CPUs:

MPI multipoint interface;
determination of node addresses.
Restart/cycle time behavior;
stipulation of maximum cycle time and loading.
Clock bit memory;
address setting
Protection level;
definition of access rights to program and data.
System diagnostics;
definition of the handling and scope of diagnostics messages.
Watchdog interrupts;
setting of periodicity
Time-of-day interrupts;
setting of date and time of start and periodicity
PROFIBUS DP master/slave interface;
user-oriented address allocation for distributed I/O.

Indication and information functions

Status and error indications;
LEDs indicate e.g. hardware, programming, time, I/O or bus errors, as well as operating states such as RUN, STOP and restart
Test functions;
the PG can be used to display signal states in program execution, modify process variables independently of the user program, and read out the contents of stack memories.
Information functions;
you can use the PG to obtain information about the storage capacity and operating mode of the CPU as well as the current loading of the main and load memories, current cycle times and diagnostic buffer contents in plain text.

Integrated communication functions

PG/OP communication
Global data communication
S7 basic communication
S7 communication (server only)

Sequential function chart

The CPU provides many extensive system functions for diagnostics, parameterization, synchronization, alerting, time measurement, etc.
Details can be found in the manual.

Communication

The safety-related communication and standard communication between the central controller and the distributed stations is conducted over PROFIBUS DP. The specially developed PROFIBUS profile PROFIsafe allows the transmission of user data associated with the safety function within the standard data telegram. Additional hardware components, e.g. special safety buses, are unnecessary. The required software is either integrated in the hardware components as an extension of the operating system, or must be loaded into the CPU as a certified software component.

Mode of operation

The safety functions of the F CPU are contained in the CPU's F program and in the fail-safe signal modules. The signal modules monitor the output and input signals by means of discrepancy analyses and test signal injections. The CPU monitors proper operation of the PLC by performing regular self-tests, instruction tests and logic and sequential program flow control. In addition, the I/O is checked by requesting signs of life. If an error is diagnosed on the system, the latter is moved to a safe state. An F runtime license is not required for operation of the CPU 317F-2 DP.

Programming

The CPU 317F-2 DP is programmed in the same manner as other SIMATIC S7 systems. The user program for non fail-safe plant sections is created with the proven programming tools such as STEP 7.

SIMATIC S7 Distributed Safety option package

The "S7 F Distributed Safety" option package is required to program the safety-relevant parts of the program. The package contains all the functions and blocks required to create the F program. The F program with the safety functions is linked in F-FBD or F-LAD or using special function blocks from the F library. Use of F-FBD or F-LAD simplifies plant planning and programming and, because of the uniform and cross-vendor presentation, the acceptance test too. Programmers can concentrate completely on configuration of the safety-relevant application without having to use additional tools.

	6ES7 317-6FF04-0AB0
Product version
Hardware product version	01
Firmware version	V3.3
General information
associated programming package	STEP 7 V5.5 + SP1 or higher or STEP7 V5.2 + SP1 or higher with HSP 202 + Distributed Safety
Supply voltage
24 V DC	Yes
Input current
Current consumption (rated value)	870 mA
Current consumption (in no-load operation), typ.	120 mA
Inrush current, typ.	4 A
I²t	1 A²·s
Power losses
Power loss, typ.	4.5 W
Memory
Work memory
integrated	1 536 Kibyte
expandable	No
Size of retentive memory for retentive data blocks	256 Kibyte
Load memory
pluggable (MMC)	Yes
pluggable (MMC), max.	8 Mbyte
Data management on MMC (after last programming), min.	10 a
Backup
present	Yes; Guaranteed by MMC (maintenance-free)
without battery	Yes; Program and data
CPU-blocks
Number of blocks (total)	2 048; (DBs, FCs, FBs); the maximum number of loadable blocks can be reduced by the MMC used.
DB
Number, max.	2 048; Number range: 1 to 16000
Size, max.	64 Kibyte
FB
Number, max.	2 048; Number range: 0 to 7999
Size, max.	64 Kibyte
FC
Number, max.	2 048; Number range: 0 to 7999
Size, max.	64 Kibyte
OB
Size, max.	64 Kibyte
Nesting depth
per priority class	16
additional within an error OB	4
CPU processing times
for bit operations, min.	0.025 µs
for word operations, min.	0.03 µs
for fixed point arithmetic, min.	0.04 µs
for floating point arithmetic, min.	0.16 µs
Counters, timers and their retentivity
S7 counter
Number	512
Retentivity
adjustable	Yes
lower limit	0
upper limit	511
preset	Z 0 to Z 7
Counting range
lower limit	0
upper limit	999
IEC counter
present	Yes
Type	SFB
Number	Unlimited (limited only by RAM capacity)
S7 times
Number	512
Retentivity
adjustable	Yes
lower limit	0
upper limit	511
preset	No retentivity
Time range
lower limit	10 ms
upper limit	9 990 s
IEC timer
present	Yes
Type	SFB
Number	Unlimited (limited only by RAM capacity)
Data areas and their retentivity
retentive data area, total	All, max. 256 KB
Flag
Number, max.	4 096 byte
Retentivity available	Yes; MB 0 to MB 4095
Retentivity preset	MB 0 to MB 15
Number of clock memories	8; 1 memory byte
Data blocks
Retentivity adjustable	Yes; via non-retain property on DB
Retentivity preset	Yes
Local data
per priority class, max.	32 768 byte; Max. 2048 bytes per block
Address area
I/O address area
Inputs	8 192 byte
Outputs	8 192 byte
of which, distributed
Inputs	8 192 byte
Outputs	8 192 byte
Process image
Inputs, adjustable	8 192 byte
Outputs, adjustable	8 192 byte
Inputs, default	1 024 byte
Outputs, default	1 024 byte
Subprocess images
Number of subprocess images, max.	1
Digital channels
Inputs	65 536
Outputs	65 536
Inputs, of which central	1 024
Outputs, of which central	1 024
Analog channels
Inputs	4 096
Outputs	4 096
Inputs, of which central	256
Outputs, of which central	256
Hardware configuration
Racks, max.	4
Modules per rack, max.	8
Expansion devices, max.	3
Number of DP masters
integrated	2
via CP	4
Number of operable FMs and CPs (recommended)
FM	8
CP, point-to-point	8
CP, LAN	10
Time of day
Clock
Hardware clock (real-time clock)	Yes
battery-backed and synchronizable	Yes
Deviation per day, max.	10 s; Typ.: 2 s
Backup time	6 wk; At 40 °C ambient temperature
Behavior of the clock following POWER-ON	Clock continues running after POWER OFF
Behavior of the clock following expiry of backup period	Clock continues to run with the time at which the power failure occurred
Operating hours counter
Number	4
Number/Number range	0 to 3
Range of values	0 to 2^31 hours (when using SFC 101)
Granularity	1 hour
retentive	Yes; Must be restarted at each restart
Clock synchronization
supported	Yes
to MPI, master	Yes
to MPI, slave	Yes
to DP, master	Yes; With DP slave only slave clock
to DP, slave	Yes
in AS, master	Yes
in AS, slave	Yes
on Ethernet via NTP	No
1st interface
Type of interface	Integrated RS 485 interface
Physics	RS 485
Isolated	Yes
Power supply to interface (15 to 30 V DC), max.	200 mA
Functionality
MPI	Yes
DP master	Yes
DP slave	Yes
Point-to-point connection	No
MPI
Services
PG/OP communication	Yes
Routing	Yes
Global data communication	Yes
S7 basic communication	Yes
S7 communication	Yes; Only server, configured on one side
S7 communication, as client	No; but via CP and loadable FB
S7 communication, as server	Yes
Transmission rate, max.	12 Mbit/s
DP master
Services
PG/OP communication	Yes
Global data communication	No
S7 basic communication	Yes; I blocks only
S7 communication	Yes; Only server, configured on one side
S7 communication, as client	No
S7 communication, as server	Yes
Equidistance mode support	Yes
Isochronous mode	No
SYNC/FREEZE	Yes
Activation/deactivation of DP slaves	Yes
Number of DP slaves that can be simultaneously activated/deactivated, max.	8
Direct data exchange (slave-to-slave communication)	Yes; As subscriber
DPV1	Yes
Transmission rate, max.	12 Mbit/s
Number of DP slaves, max.	124
Address area
Inputs, max.	8 Kibyte
Outputs, max.	8 Kibyte
User data per DP slave
Inputs, max.	244 byte
Outputs, max.	244 byte
DP slave
Services
PG/OP communication	Yes
Global data communication	No
S7 basic communication	No
S7 communication	Yes; Only server, configured on one side
S7 communication, as client	No
S7 communication, as server	Yes; Connection configured on one side only
Direct data exchange (slave-to-slave communication)	Yes
DPV1	No
Transmission rate, max.	12 Mbit/s
Automatic baud rate search	Yes; only with passive interface
Transfer memory
Inputs	244 byte
Outputs	244 byte
Address area, max.	32
User data per address area, max.	32 byte
2nd interface
Type of interface	Integrated RS 485 interface
Physics	RS 485
Isolated	Yes
Power supply to interface (15 to 30 V DC), max.	200 mA
Functionality
MPI	No
DP master	Yes
DP slave	Yes
Local Operating Network	No
DP master
Services
PG/OP communication	Yes
Global data communication	No
S7 basic communication	Yes; I blocks only
S7 communication	Yes; Only server, configured on one side
S7 communication, as client	No; but via CP and loadable FB
S7 communication, as server	Yes
Equidistance mode support	Yes
Isochronous mode	Yes; OB 61
SYNC/FREEZE	Yes
Activation/deactivation of DP slaves	Yes
Number of DP slaves that can be simultaneously activated/deactivated, max.	8
Direct data exchange (slave-to-slave communication)	Yes; As subscriber
DPV1	Yes
Transmission rate, max.	12 Mbit/s
Number of DP slaves, max.	124
Address area
Inputs, max.	8 192 byte
Outputs, max.	8 192 byte
User data per DP slave
Inputs, max.	244 byte
Outputs, max.	244 byte
DP slave
Services
PG/OP communication	Yes
Global data communication	No
S7 basic communication	No
S7 communication	Yes; Only server, configured on one side
S7 communication, as client	No; but via CP and loadable FB
S7 communication, as server	Yes
Direct data exchange (slave-to-slave communication)	Yes
DPV1	No
GSD file	The latest GSD file is available on the Internet (http://www.siemens.com/profibus-gsd)
Transmission rate, max.	12 Mbit/s
Automatic baud rate search	Yes; only with passive interface
Transfer memory
Inputs	244 byte
Outputs	244 byte
Address area, max.	32
User data per address area, max.	32 byte
Communication functions
PG/OP communication	Yes
Data record routing	Yes
Global data communication
supported	Yes
Number of GD loops, max.	8
Number of GD packets, max.	8
Number of GD packets, transmitter, max.	8
Number of GD packets, receiver, max.	8
Size of GD packets, max.	22 byte
Size of GD packet (of which consistent), max.	22 byte
S7 basic communication
supported	Yes
User data per job, max.	76 byte
User data per job (of which consistent), max.	76 byte; 76 bytes (with X_SEND or X_RCV); 64 bytes (with X_PUT or X_GET as server)
S7 communication
supported	Yes
as server	Yes
as client	Yes; Via CP and loadable FB
User data per job, max.	See online help of STEP 7 (shared parameters of the SFBs/FBs and of the SFCs/FCs of S7 Communication)
S5-compatible communication
supported	Yes; via CP and loadable FC
Number of connections
usable for routing	X1 as a MPI, max. 10; X1 as DP Master max. 24; X1 as DP Slave (active) max. 14; X2 as DP Master max. 24; X2 as DP Slave (active) max. 14
S7 message functions
Number of login stations for message functions, max.	32; Depending on the configured connections for PG/OP and S7 basic communication
Process diagnostic messages	Yes
simultaneously active Alarm-S blocks, max.	300
Test commissioning functions
Status/control
Status/control variable	Yes
Variables	Inputs, outputs, memory bits, DB, times, counters
Number of variables, max.	30
of which status variables, max.	30
of which control variables, max.	14
Forcing
Forcing	Yes
Force, variables	Inputs, outputs
Number of variables, max.	10
Status block	Yes; Up to 2 simultaneously
Single step	Yes
Number of breakpoints	4
Diagnostic buffer
present	Yes
Number of entries, max.	500
adjustable	No
Of which powerfail-proof	100; Only the last 100 entries are retained
Number of entries readable in RUN, max.	499
adjustable	Yes; From 10 to 499
preset	10
Ambient conditions
Operating temperature
Min.	0 °C
max.	60 °C
Configuration
Configuration software
STEP 7	Yes; STEP7 as of V5.5 + SP1 or STEP 7 V5.2 + SP1 or higher with HSP 202
STEP 7 Lite	No
programming
Programming language
LAD	Yes
FBD	Yes
STL	Yes
SCL	Yes
CFC	Yes
GRAPH	Yes
HiGraph®	Yes
Command set	see instruction list
Nesting levels	8
Know-how protection
User program protection/password protection	Yes
Block encryption	Yes; With S7 block Privacy
Dimensions
Width	40 mm
Height	125 mm
Depth	130 mm
Weight
Weight, approx.	360 g

Код	Заказной номер	Описание	Вес (кг)	Заказать
109050	6AG1305-1AA00-2AA0	siplus upmiter 4a, рабочая температура -25... +60 градусов цельсия, (s7-300-style)	1.2	Заказать
109067	6AG1317-6FF03-2AB0	siplus s7-300 модуль цпу cpu317f-2dp (1mb), темп. диапазон от -25... +60 град. цельсия, на базе модуля 6es7317-6ff03-0ab0	0.529	Заказать
109068	6AG1317-6FF03-2AY0	siplus s7-300, модуль цпу cpu317f-2dp, расширенный диапазон рабочих температур -25... + 60 градусов цельсия согласно en50155, на основе модуля 6es7317-6ff00-0ab0	0.529	Заказать
110756	6ES7391-1AA00-0AA0	simatic s7-300, запасной съемный соединитель для подключения цепей питания =24в к центральным процессорам s7-300 compact и модулю fm352-5, упаковка из 10 штук	0.061	Заказать
110780	6ES7398-8EA00-8AA0	simatic s7-300/-400, руководство по связи s7-300/-400, немецкий язык	0.585	Заказать
110781	6ES7398-8EA00-8BA0	simatic s7-300/-400, руководство по связи s7-300/-400, английский язык	0.568	Заказать
110782	6ES7398-8FA10-8AA0	simatic s7-300 compact, руководство по конфигурированию, технические характеристики центральных процессоров, технические характеристики модулей, список инструкций, немецкий язык	5	Заказать
110783	6ES7398-8FA10-8BA0	simatic s7-300 compact, руководство по конфигурированию, технические характеристики центральных процессоров, технические характеристики модулей, список инструкций, английский язык	5	Заказать
63144	6ES7833-1FC02-0YA5	simatic s7, f средство разработки распределенных систем повышенной безопасности distributed safety v5.4, плавающая лицензия для 1 пользователя, инженерное прогр. обеспечение, прогр. обесп. и документация на cd, class a, 3 языка (нем., англ.,франц.), работа под step7 v5.3 sp3	0.257	Заказать
63145	6ES7833-1FC02-0YE5	simatic s7, f средство программирования distributed safety v5.4, пакет обновления от версии 5.x до версии 5.4, плавающая лицензия для 1 пользователя, инженерное прогр. обеспечение, прогр. обесп. и документация на cd, class a, 3 языка (нем., англ.,франц.), работа под step7 v5.3 sp3	0.257	Заказать
63182	6ES7901-0BF00-0AA0	simatic s7, mpi-кабель для подключения simatic s7 к программатору через mpi, длина 5m	0.274	Заказать
111168	6ES7912-0AA00-0AA0	simatic s7, пластиковые метки маркироки номеров модулей в монтажных стойках s7-300/ s7-400/ et 200m/ c7	0.006	Заказать
111241	6ES7953-8LF20-0AA0	simatic s7, микрокарта памяти mmc для s7-300/c7/et 200, 3.3 в nflash, 64 кбайт	0.012	Заказать
111242	6ES7953-8LG20-0AA0	simatic s7, микрокарта памяти mmc для s7-300/c7/et 200, 3.3 в nflash, 128 кбайт	0.014	Заказать
111243	6ES7953-8LJ30-0AA0	simatic s7, micro memory card f. s7-300/c7/et 200, 3.3 v nflash, 512 kbytes	0.012	Заказать
111244	6ES7953-8LL20-0AA0	simatic s7, микрокарта памяти mmc для s7-300/c7/et 200, 3.3 в nflash, 2 мбайт	0.012	Заказать
111245	6ES7953-8LM20-0AA0	simatic s7, микрокарта памяти mmc для s7-300/c7/et 200, 3.3 в nflash, 4 мбайт	0.012	Заказать
111246	6ES7953-8LP20-0AA0	simatic s7, микрокарта памяти mmc для s7-300/c7/et 200, 3.3 в nflash, 8 мбайт	0.013	Заказать
111255	6ES7972-0AA02-0XA0	simatic dp, rs485-повторитель для подключения шинной системы profibus/mpi bus systems с макс. 31 узлом; макс. 12 мбит/с, степень защиты ip20, улучшенные пользовательские свойства	0.289	Заказать
63269	6ES7972-0BA12-0XA0	simatic dp, соединитель для подключения к profibus, до 12 мбит/с, отвод кабеля под углом 90 градусов, 15.8 x 54 x 34 mm, с встроенным терминальным резистором, с функциями разделения, без гнезда для подключения программатора	0.049	Заказать
111257	6ES7972-0BA52-0XA0	simatic dp, шинный оединитель для подключения к сетям profibus до 12 мбит/с, отвод кабеля под углом 90 градусов, 15,8 x 59 x 35,6 mm (шxвxг), ipcd, технология fast connect, без разъёма для подключения программатора	0.044	Заказать
111258	6ES7972-0BA52-0XB0	simatic dp,bus connector for profibus up to 12 mbit/s 90 degree angle outgoing cable, 15,8 x 59 x 35,6 mm (wxhxd), ipcd techology fast connect, without pg socket 100 pieces per packaging unit	4.5	Заказать
111260	6ES7972-0BB12-0XA0	simatic dp, соединитель для подключения к profibus, до 12 мбит/с, отвод кабеля под углом 90 градусов, 15.8 x 54 x 34 mm, с встроенным терминальным резистором, с функциями разделения, с гнездом для подключения программатора	0.056	Заказать
63271	6ES7972-0BB52-0XA0	simatic dp, шинный оединитель для подключения к сетям profibus до 12 мбит/с, отвод кабеля под углом 90 градусов, 15,8 x 59 x 35,6 mm (шxвxг), ipcd, технология fast connect, с разъёмом для подключения программатора	0.049	Заказать
111262	6ES7972-0BB52-0XB0	simatic dp,bus connector for profibus up to 12 mbit/s 90 degree angle outgoing cable, 15,8 x 59 x 35,6 mm (wxhxd), ipcd techology fast connect, with pg socket 100 pieces per packaging unit	5	Заказать
63274	6ES7972-0CB20-0XA0	simatic s7, pc usb адаптер для подкл. simatic s7-200/s7-300/ s7-400/ c7 к компьютеру/ программатору через usb интерфейс: pc usb адаптер, cd с набором драйверов и док., usb кабель длиной 5 м, mpi кабель длиной 0.3 м. работа под упр. win 2000/xp	0.526	Заказать
63287	6ES7998-8XC01-8YE0	коллекция руководств simatic на cd-rom. pdf-формат, анг/ нем/ фр/ исп/ ит. язык. все руководства по s7-200/ -300/ -400/ -c7/ -logo!; simatic dp/ -pc/ -pg; step7, инстр. средствам проектирования, прогр. обеспечению runtime, simatic pcs7/ hmi/ net	0.2	Заказать
63288	6ES7998-8XC01-8YE2	коллекция руководств simatic на cd-rom, 5-языковая поддержка (без русского), служба обновления в течение 1 года	0.4	Заказать
114346	6GK1500-0EA02	simatic net, pb шинный соединитель с осевым отводом кабеля для пром. пк, simatic op, olm; скорость передачи 12 мбит/с, оконечный резистор с функциями разделения	0.104	Заказать
116945	6XV1830-0EH10	simatic net, стандартный экранированный profibus кабель для быстрого монтажа (fc), 2-жильный, поставка по метражу отрезками длиной 20 ... 1000 m	0.081	Заказать